Aqualube® 2029 is a water miscible, heavy duty non-chlorinated, non-sulfurized synthetic compound for medium to heavy drawing, stamping and blanking operations for steel and galvanized. It provides excellent lubricity and leaves a light, protective film to provide post process corrosion protection on steel. Cellotone® 50 is a highly alkaline powder based material containing chelants and nonionic wetting agents. Low foaming properties makes it suitable for “wet end” boil-outs where a high degree of agitation usually exists. Cellotone® 62-L is a caustic soda based liquid containing chelants and anionic wetting agents. A low foaming nature makes it suitable for “wet end” boil-outs where a high degree of agitation usually exists. Hamico® 8928 is an additive for metalworking fluids to improve effectiveness of the biocides in the fluid and to raise and stabilize pH. It possesses reserve alkalinity and is bio-resistant in nature. It is effective with synthetic, semi-synthetic, or soluble oils. It effectively neutralizes any acidic components in a solution and maintains fluid performance and longevity. It protects against production of acidic by products in the system through bioresistant properties. Hamistrip® 1650 is for easy removal of most shop soils like soluble oil, grease and metal chips and fines. It is an alkaline rust and paint remover combining caustics and organic acids Hamiterge® 2031-C2 is a concentrated liquid alkaline spray cleaner for removal of rolling oil residues, metallic chips and fines, oily soils, and shop or mill dirt from sheet steel surfaces and other ferrous metal parts. It is designed for usage in power spray washers or roto-brush type cleaning equipment at elevated or ambient temperature conditions in dilutions with water. It is low foaming, completely biodegradable and free rinsing. It splits out cleaned soils readily and maintains low foaming characteristics when soils accumulate that can form soaps. Hamiterge® 2038-LFM is a highly caustic liquid alkaline cleaner for immersion cleaning operations requiring a strongly alkaline solution. It is for removal of extremely difficult soils from ferrous metal surfaces at elevated temperatures. It has excellent wetting and detergency. It can be used at high concentration and elevated temperature for removal of phosphate coatings and drawing lube residues from steel parts, such as tube, rod, bar, or wire. It is completely soluble in water and is free rinsing. Hamiterge® 8922 is a concentrated liquid alkaline spray cleaner for removal of rolling oil residues, drawing and stamping lubricants, rust preventives, metallic chips and fines, and other oily soils, shop or mill dirt from steel strip, wire, rod and bars. It is designed for use in power spray washers or roto-brush type cleaning equipment at elevated or ambient temperatures in dilutions with water. It is low foaming, completely biodegradable, and free rinsing. It will not buildup hard water deposits and contains no phosphates. Mill Purge® 1812 is an industrial maintenance cleaner for floors, machinery, sumps, kettles and vats, etc. It is also used in ultrasonic cleaning, dip tank cleaning of steel, cast iron and aluminum parts and equipment. Hamico® Neutralizer 809-L is a combination of liquid alkalis and surface-active (wetting) agents designed specifically for neutralizing acidic residues from ferrous metals after pickling operations. Hamiterge® 711-2 is an extremely high strength powdered alkaline cleaner consisting of exceptional wetting agents and detergents in a base of alkaline builders. It is an immersion cleaner designed for low or high temperature applications. It will remove rolling oils and other mill soils from all steel surfaces, including stainless and galvanized. It is also applicable for use in high speed scrubber systems. It is lower foaming at higher operating temperatures, (160 F and above) and is completely free rinsing with water. It is also available in a low foam version (Hamiterge® 711-2-LF) for spray washers. Hamiterge® 711-5 is a powdered alkaline cleaner designed for immersion cleaning of mill soils from steel surfaces and can be used on aluminum, copper and brass. It is also available in a low foam version (Hamiterge® 711-5-LF) for spray washers. | 
