Citriterge® 8910 is a cleaner consisting of natural citrus based solvents, surfactants and detergent components. It is designed to remove dirt, grease, oil and carbon smuts from metals and other hard surfaces. It also removes tar, pitch, asphalt, and gum soils from felts in papermaking operations. Citriterge® 8910 performs heavy duty cleaning without the use of petrochemical solvents, chlorinated solvents and harsh acids or alkalis. Hamico® 863-EP Base is normally used as received, but can be diluted with oil, solvents, or water, depending on the operation. It may be applied by dipping, spray, or brushing. It is a combination of extreme pressure lubricants. It is used either neat or with oil. It is used primarily for tapping operations on steel. It will not corrode steel or aluminum on contact, but will stain brass and copper. Hamidraw® 1828-A is a heavy duty, water soluble, extreme pressure lubricant offering maximum lubricity for drawing, ferrous and non-ferrous metals, including stainless steel. The residual film offers corrosion protection for the drawn parts. Hamidraw® 1828-DS is a heavy duty, water soluble drawing compound for lubrication of steel and non-ferrous metals in drawing operations. Hamidraw® 1829 is an ultra-heavy duty, water soluble, extreme pressure lubricant, offering maximum lubricity for drawing, ferrous and non-ferrous metals, including stainless steel. It is designed for extremely difficult draws to provide maximum extreme pressure lubrication and is non-staining to metals and carbide dies. The residual film offers corrosion protection for the drawn parts. If diluted at 1:1 with water, Hamidraw® 1829 forms a low viscosity, stable emulsion. Hamidraw® 1829 can also be diluted with petroleum solvents or mineral oils. Hamidraw® 1829 is suited to spray application or direct flood application onto workpiece or dies. Hamidraw® 1846-B is a heavy duty pigmented drawing lubricant for ferrous or stainless steels. It is utilized for extremely severe draws such as tube reducing, bar drawing, wire drawing when reductions up to 40% are required. The lubricant cleans quickly with hot alkaline or hot detergent cleaning. Hamidraw® 9100-B is an entirely non-chlorinated extreme pressure lubricant for heavy duty drawing and stamping. It contains a polymeric lubricant package which provides the extreme pressure lubricating properties of the chlorinated additives formerly used. Hamidraw® 9100-B is environmentally acceptable and has enhanced removability characteristics. Hamikleer® 1995 is a bio-resistant synthetic machining and grinding lubricant/coolant for ferrous and non-ferrous metals. It is extremely low foaming, which makes it useful in operations where foam control is essential, such as double disc or plunge grinding, or high speed machining. It provides lubrication needed for moderate to heavy duty machining operations, such as turning, drilling, reaming, broaching, boring and tapping. It is non-staining to non-ferrous metals, (e.g., copper alloys and aluminum), contains extreme pressure friction reducing lubricant additives, and provides good lubrication and rust protection to steel. Hamikleer® 1995 has a liquid residual film, which keeps machinery parts moving, and has excellent wetting to keep swarf and fines from depositing on machinery, and enabling them to settle out quickly in central sumps. It rejects contaminants such as most tramp oils and is highly bacterial resistant, which extends sump life of central and individual systems. Hamikut® 100 is a new technology soluble oil metalworking lubricant that offers excellent bioresistance and stability to coolant systems. It can perform a wide variety of machining and grinding operations on both ferrous and non-ferrous metals. It offers cooling, excellent friction reduction, extremely low foam and will not sour with microbial contamination. It is free of substances subject to the reporting requirements of SARA Title III. It provides superior rust protection when used in sumps which typically encounter large amounts of contaminants. It is ideal for use in central systems. It is extremely easy to handle using filtration or centrifuge, and will not clog paper or filters. Hamikut® 9036-B is an enhanced heavy duty soluble oil lubricant for heavy duty machining of ferrous and non-ferrous metals, including zinc. Provides corrosion protection, is low foaming, possesses excellent emulsion stability and produces good micro-finishes. It provides improved biological control capability for longer sump life in re-circulating systems. Hamikut® 9120-NC is an extremely effective chlorine free soluble oil for light and medium duty machining and grinding of steel, alloys, aluminum, and yellow non ferrous metals, like copper, brass or bronze. It produces superior micro-finishes, while maintaining stability in hard water. It has improved bio-resistance properties. It is designed for recycling and centrifuging, and is very low foaming. It produces an ultra-stable blue emulsion. Hamilube® 7709 is a non-chlorinated straight oil containing friction-reducing extreme pressure additives, which makes it suitable for drilling operations. It is also applicable for threading, tapping, turning, milling, trepanning and other machining operations on steel. Used on Stainless and Alloyed steels. It contains sulfurized additives and has a light viscosity, which makes it suitable for gun drilling. It will provide an adequate fluid film between the wear pads and the work material, will prevent welding of chips to the cutting edge of the drill, will cool the drill and the work, and dispose of the chips easily by flushing. Aqualube® 2023 FR is a water miscible, synthetic compound for light to medium drawing, stamping and blanking operations of all metals. This product provides excellent lubricity and leaves a light, protective film. Aquaroll® 7606-FO is an emulsifiable cold rolling lubricant for steel, copper and brass. It is applicable for use in grade rolling of blanks in tableware manufacture. It is non-staining to rolls and work, contains little ash, is long lasting and low foaming. Hamidraw® 497-B is composed of extreme pressure resisting chlorinated base and synthetic esters. It contains no pigments, is non-flammable and is completely removable in mineral or chlorinated solvents. It will not channel and is cohesive and adhesive. The viscosity of this product can be reduced by cutting back with solvents or mineral oils. Hamidraw® 1828-LC is a heavy duty, water soluble drawing compound for lubrication of steel and non-ferrous metals in drawing operations. It has a reduced amount of extreme pressure lube additives from the Hamidraw® 1828-DS version. Hamidraw® 1846-NC is a heavy duty non-chlorinated pigmented drawing lubricant for ferrous or stainless steels. It can be used for severe draws such as tube reducing, bar drawing, wire drawing, etc. The lubricant cleans quickly with hot alkaline or hot detergent cleaning. Hamidraw® 1945 Series (100-700) is a lubricant for blanking and deep drawing of all metals. It is a heavy duty oil and can be cut back with mineral oil for lighter work. Removal from the metal can be done with solvents or alkaline cleaners. Hamidraw® 1945 is offered in various viscosity grades. Hamidraw® 9014-LV and 9019 are tube hydroforming lubricants for applications to the outer diameter of parts being formed into dies. Both products are straight petroleum based lubes containing advanced additive packages that are free of sulfur, chlorine, and pigmented compounds. They have excellent forming characteristics and compare very favorably to chlorinated and sulfurized lubes when used on hydroforming operations involving severe metal deformation and elongation. Hamidraw® 9014-LV is a lighter viscosity version of the two products. Hamidraw® 9019 is heavier and possesses better film adherence properties. Hamikleer® 1975 HD is a synthetic machining lubricant/coolant for ferrous and non-ferrous metals. It provides the needed lubrication for light or heavy machining operations including: boring, drilling, reaming, tapping, and threading. It is non-staining to non-ferrous metals, e.g., copper, brass, and aluminum and has a liquid residual film, which keeps machinery parts moving.
Hamikleer® 2095 is a synthetic grinding and machining coolant concentrate designed to be used on both ferrous metals, non-ferrous metals, and also on milling of scale from copper or brass strip. Solutions provide excellent rust protection for cast iron and ferrous alloys with no staining on zinc, copper, brass, and bronze. The solution keeps wheels clean and suspends metallic fines and swarf, preventing their precipitation on ways, tables, and other work surfaces. It will not turn rancid and does not cause dermatitis. Hamikut®1860-LC is a heavy duty soluble oil cutting and machining fluid. It contains extreme pressure lubricating additives which are low in color and odor, yet provide the greatest degree of lubrication for extreme surface and internal grinding operations where problems, such as burning, often develop. It can be used on carbon steel, stainless, and non-ferrous metals including aluminum, copper, and brass. Hamilube® 1744 is a straight oil containing extreme pressure additives for general machining of all metals, including Magnesium. Steelgard® X-267-B is a long term, outdoor rust preventive that can be used on ferrous or non-ferrous metals, in uncovered or covered storage conditions. It protects tools, stampings, forgings, castings, machinery, tubing or any metal parts that need a waxy, plastic, non-tacky film. It protects overseas and domestic shipments. |
