Steelgard® 1302-J is for rust protection of all ferrous metals, including cast and malleable iron. It is ideal for spray washer application for mild cleaning and rust protection. Atmoscleer® 8001 is a foam blanket additive for hydrochloric acid batch pickling baths. It imparts a densely packed, uniform layer of foam on the surface of a steel pickling bath. Some agitation may be required to generate the foam layer when there is not enough pickling action occurring, such as when the bath temperature is very low (below 1000F). It is extremely stable in hydrochloric acid baths containing high amounts of dissolved iron and under high temperature conditions. It cuts down on heat loss and holds corrosive hydrochloric fumes in the bath. It should be used in conjunction with Activol® acid inhibitors for hydrochloric acids, such as Activol® 1803, Activol® 1590-C, Activol® 1590–CP or Activol® 1903 for best results in batch pickling operations. Aqualube® 2023 FR is a water miscible, synthetic compound for light to medium drawing, stamping and blanking operations of all metals. This product provides excellent lubricity and leaves a light, protective film. Aquaroll® 7606-FO is an emulsifiable cold rolling lubricant for steel, copper and brass. It is applicable for use in grade rolling of blanks in tableware manufacture. It is non-staining to rolls and work, contains little ash, is long lasting and low foaming. Hamidraw® 9100-B is an entirely non-chlorinated extreme pressure lubricant for heavy duty drawing and stamping. It contains a polymeric lubricant package which provides the extreme pressure lubricating properties of the chlorinated additives formerly used. Hamidraw® 9100-B is environmentally acceptable and has enhanced removability characteristics. Hamikleer® 712-2 is a water soluble synthetic couplant for ultrasonic testing replacing glycerine. The buffering action permits testing of many metals and metallic couples that heretofore corroded in aqueous-phase couplants. The low halogen content makes Hamikleer® 712-2 ideal for use on titanium and other space-age metals where possible halogen stress corrosion could be a problem. When used neat, the product’s viscosity permits testing of vertical surfaces while exceptional water solubility and solution clarity allow easier rigging and positioning in submerged tank testing. Hamikleer® High Viscosity U.T. Couplants is a series of high viscosity versions of Hamikleer® 712-2 for ultrasonic testing of metals:
Hamikleer® 712-HV-1 Viscosity - 38,000 - 45,000 cps @ 720F
Hamikleer® 712-HV-2 Viscosity - 27,000 - 33,000 cps@ 720F
Hamikleer® 712-HV-3 Viscosity - 5,000 - 8,000 cps @ 720F
Hamikleer® 1990 is a bio-resistant synthetic machining and grinding lubricant/coolant for ferrous and non-ferrous metals. It is extremely low foaming, which makes it useful in operations where foam control is essential, such as double disc or plunge grinding, or high speed machining. It provides lubrication needed for light to moderate duty machining operations, such as grinding, turning, drilling, reaming, and tapping. Hamikleer® 1990 is non-staining to non-ferrous metals and has a liquid residual film, which keeps machinery parts moving and provides good lubrication and rust protection to steel. It offers excellent wetting to keep swarf and fines from depositing on machinery, while enabling them to settle out quickly in central sumps. It rapidly rejects contaminants such as most tramp oils. It is highly bacterial resistant, which extends sump life of central and individual systems. Hamikleer® 1995 is a bio-resistant synthetic machining and grinding lubricant/coolant for ferrous and non-ferrous metals. It is extremely low foaming, which makes it useful in operations where foam control is essential, such as double disc or plunge grinding, or high speed machining. It provides lubrication needed for moderate to heavy duty machining operations, such as turning, drilling, reaming, broaching, boring and tapping. It is non-staining to non-ferrous metals, (e.g., copper alloys and aluminum), contains extreme pressure friction reducing lubricant additives, and provides good lubrication and rust protection to steel. Hamikleer® 1995 has a liquid residual film, which keeps machinery parts moving, and has excellent wetting to keep swarf and fines from depositing on machinery, and enabling them to settle out quickly in central sumps. It rejects contaminants such as most tramp oils and is highly bacterial resistant, which extends sump life of central and individual systems. Hamikleer® 2095 is a synthetic grinding and machining coolant concentrate designed to be used on both ferrous metals, non-ferrous metals, and also on milling of scale from copper or brass strip. Solutions provide excellent rust protection for cast iron and ferrous alloys with no staining on zinc, copper, brass, and bronze. The solution keeps wheels clean and suspends metallic fines and swarf, preventing their precipitation on ways, tables, and other work surfaces. It will not turn rancid and does not cause dermatitis. Hamikleer® 8307-A and 8307-B are water soluble synthetic couplants for contact ultrasonic testing replacing glycerin. They are chemically pure couplants that contain little or no contamination, which makes them acceptable for the testing requirements of turbine blade manufacturers. They are more highly pure compounds than the Hamikleer® 712 series of couplants. Immunol® 791-J is a mild detergent and rust inhibiting chemical for use on cast iron, cast steel and other ferrous metals. It protects cast iron and ferrous metals submerged in its solution indefinitely. It forms invisible, quick drying protective coatings on metal, which insure maximum “indoor” protection. Immunol® 985-J is a low foaming detergent spray cleaner for metal surfaces. It contains rust preventives which protect ferrous metals after cleaning for short periods indoors. It is a completely nitrite free product. It removes mineral and fatty mill soils completely without saponification; therefore, it is not spent in use. Immunol® 1228 is an additive for use in non destructive test applications such as ultrasonic inspection or hydrostatic (or pressure) testing. It provides rust protection and reduced surface tension to water baths used for immersion testing of these types. Is recommended for systems constructed of (or used for testing) steel and aluminum. It is low foaming and long lasting and provides protection against flash rusting and short term indoor storage. Immunol® 1357-2-J is a clear, medium body, green liquid. It is odorless, non-flammable and pH 7.0 neutral. It is used in paper manufacturing as calendar roll cleaner and felt conditioner. It is used as additive to soluble oil (or synthetic) systems to emulsify “tramp” or hydraulic oil, loosen sludge, settle heavy particles, lift “fines” or lighter bodies to the surface. This product prevents stains or rust on ground or polished work and prevents “smut” formation in rolling when added to the soluble rolling oil. It is also a successful and economical machine, floor and wall cleaner mixed with plain water at 2 to 6 ounces per gallon and applied by brush, mop, or rag. Immunol® 1809-J is an additive for ultrasonic and hydrostatic testing operations. It is an ideal corrosion inhibitor for ferrous and non-ferrous metals and couples. It is also employed as a grinding coolant for light duty applications. Immunol® 1921 is a combination cleaner and rust preventive concentrate for use as a vibratory de-burring compound with water on castings of iron, steel or aluminum. Immunol ® Extra-J a detergent, wetting agent and rust preventive for cleaning and protecting most ferrous metals against rust. Not suitable for use on cast iron and cast steel. Replaces Immunol® Extra and contains no nitrosamines. Immunol® S-6-H is a detergent type cleaner for soak tank cleaning and degreasing of ferrous and non-ferrous parts. It emulsifies oils such as drawing compounds and rust preventives, and removes mill soils and smut very effectively. It may also be used for general purpose cleaning as a “bucket” solvent to replace more flammable or toxic materials. If used on aluminum, extended immersion times (one hour or more) produce darkening. Use Immunol® S-6-I as an alternative for aluminum. Immunol® S-10 is for all general cleaning and degreasing of ferrous and non-ferrous parts, replacing flammable, toxic solvents and alkaline cleaners. Emulsifies oils, mill soils and provides mild indoor rust protection in one operation. For use as vibratory finishing additive, in steel mills, metalworking plants, paper and textile mills as a “general purpose” immersion cleaner. Widely used in tumbling, vibratory finishers, and as a “bucket” cleaner. Purgitol® RPV-1 is a liquid metal cleaner concentrate for use in immersion tanks, ultrasonic cleaning, or rotary barrel cleaning systems. Its use is for removal of oily soils, such as machining, grinding, or drawing oil residues, synthetic coolants, rust preventives, lubricating oils, and rolling oils. It can be used on steel, cast and malleable iron, and non-ferrous metal surfaces. Purgitol® S is the answer for machine shops seeking to replace toxic, odorous, irritating solvents in their immersion cleaning operations. Purgitol® S cleans machining and drawing oils and lubricants, yet it contains no flammable or toxic ingredients. Steelgard®1883-4 is a synthetic water soluble rust preventive concentrate for temporary indoor storage protection of steel and cast or malleable iron. Solutions provide excellent rust protection for months of indoor storage under normal conditions. It is non-staining to non-ferrous metals such as brass, bronze or copper. Steelgard® 8200-H is a synthetic rust preventive concentrate for the indoor storage protection of steel and copper coated steel. It produces a clear solution in water dilutions, so it can be utilized as a test tank additive for pressure testing of tubing. Steelgard® 9050 is a synthetic water soluble, concentrated rust preventive for temporary indoor storage protection of steel and cast or malleable iron. Solutions provide excellent rust protection for months of indoor storage under normal conditions. It darkens aluminum and other non-ferrous metals. This product deposits a film that is dry to the touch. | 
