Hamikut® 1937-A is a medium-duty, soluble oil containing extreme pressure additives used for machining and grinding ferrous and non-ferrous metals, including zinc. It provides extremely good emulsion stability and is highly tolerant to other contaminants typically carried into emulsions from prior operations. Atmoscleer® 1785 is a foam blanket and fume suppressant for sulphuric acid pickle baths. Small amounts produce a heavy foam which cuts fumes and saves energy. This product may also be used for phosphoric acid baths. Steelgard® 9050 is a synthetic water soluble, concentrated rust preventive for temporary indoor storage protection of steel and cast or malleable iron. Solutions provide excellent rust protection for months of indoor storage under normal conditions. It darkens aluminum and other non-ferrous metals. This product deposits a film that is dry to the touch. Steelgard®1883-4 is a synthetic water soluble rust preventive concentrate for temporary indoor storage protection of steel and cast or malleable iron. Solutions provide excellent rust protection for months of indoor storage under normal conditions. It is non-staining to non-ferrous metals such as brass, bronze or copper. Steelgard® 1505-TC is designed for indoor long term protection of all ferrous and non-ferrous surfaces and for outdoor covered protection of up to 6 months. It provides months of protection in humidity cabinet tests at 100% relative humidity at 100 degrees F. Kleerkut® 4900 Performs a wide variety of machining and grinding operations on both ferrous and non-ferrous metals. Kleerkut® 4900 is a bio-resistant semi-synthetic coolant, free of substances subject to the reporting requirements of SARA Title III. It provides superior rust protection when used in sumps which typically encounter large amounts of contaminants, and is ideal for use in central systems. It is low foaming , easy to clean using filtration or centrifuge, and long lasting.
Kleerkut® 4900 has two "sister" products: Kleerkut® 4900-LT and Kleerkut® 4900 HD. For more information on these products, please inquire at: info@HarryMillerCorp.com. Hamiterge® 8922 is a concentrated liquid alkaline spray cleaner for removal of rolling oil residues, drawing and stamping lubricants, rust preventives, metallic chips and fines, and other oily soils, shop or mill dirt from steel strip, wire, rod and bars. It is designed for use in power spray washers or roto-brush type cleaning equipment at elevated or ambient temperatures in dilutions with water. It is low foaming, completely biodegradable, and free rinsing. It will not buildup hard water deposits and contains no phosphates. Atmoscleer® 8001 is a foam blanket additive for hydrochloric acid batch pickling baths. It imparts a densely packed, uniform layer of foam on the surface of a steel pickling bath. Some agitation may be required to generate the foam layer when there is not enough pickling action occurring, such as when the bath temperature is very low (below 1000F). It is extremely stable in hydrochloric acid baths containing high amounts of dissolved iron and under high temperature conditions. It cuts down on heat loss and holds corrosive hydrochloric fumes in the bath. It should be used in conjunction with Activol® acid inhibitors for hydrochloric acids, such as Activol® 1803, Activol® 1590-C, Activol® 1590–CP or Activol® 1903 for best results in batch pickling operations. Aqualube® 2023 FR is a water miscible, synthetic compound for light to medium drawing, stamping and blanking operations of all metals. This product provides excellent lubricity and leaves a light, protective film. Hamico® 863-EP Base is normally used as received, but can be diluted with oil, solvents, or water, depending on the operation. It may be applied by dipping, spray, or brushing. It is a combination of extreme pressure lubricants. It is used either neat or with oil. It is used primarily for tapping operations on steel. It will not corrode steel or aluminum on contact, but will stain brass and copper. Hamico® 1003 is a light colored, transparent, odorless lubricating oil for machinery and equipment requiring an extremely clean condition with a light oil. It can be used in many applications where light lubrication is needed, e.g., forming, bending, stamping, straightening. It can be used on all metals as received, by pumping, dip, spray or wipe. Hamidraw® 1829 is an ultra-heavy duty, water soluble, extreme pressure lubricant, offering maximum lubricity for drawing, ferrous and non-ferrous metals, including stainless steel. It is designed for extremely difficult draws to provide maximum extreme pressure lubrication and is non-staining to metals and carbide dies. The residual film offers corrosion protection for the drawn parts. If diluted at 1:1 with water, Hamidraw® 1829 forms a low viscosity, stable emulsion. Hamidraw® 1829 can also be diluted with petroleum solvents or mineral oils. Hamidraw® 1829 is suited to spray application or direct flood application onto workpiece or dies. Hamidraw® 1846-B is a heavy duty pigmented drawing lubricant for ferrous or stainless steels. It is utilized for extremely severe draws such as tube reducing, bar drawing, wire drawing when reductions up to 40% are required. The lubricant cleans quickly with hot alkaline or hot detergent cleaning. Hamikut® 9036-B is an enhanced heavy duty soluble oil lubricant for heavy duty machining of ferrous and non-ferrous metals, including zinc. Provides corrosion protection, is low foaming, possesses excellent emulsion stability and produces good micro-finishes. It provides improved biological control capability for longer sump life in re-circulating systems. Hamilube® 1955-A is a straight oil non-chlorinated lubricant that contains extreme pressure additives for the general machining of tool steel and stainless steel. It contains no chlorinated compounds or phosphorus. It is transparent to allow viewing of the work piece during machining. It is not suitable for use with non-ferrous metals. It contains active sulfur and is non-staining on steel. Hamilube® 5705 is a straight oil containing extreme pressure additives for the general machining of tool steel and stainless steel. It contains no chlorinated compounds, phosphorus or animal fats. Not suitable for use with non-ferrous metals. Purgitol® RPV-1 is a liquid metal cleaner concentrate for use in immersion tanks, ultrasonic cleaning, or rotary barrel cleaning systems. Its use is for removal of oily soils, such as machining, grinding, or drawing oil residues, synthetic coolants, rust preventives, lubricating oils, and rolling oils. It can be used on steel, cast and malleable iron, and non-ferrous metal surfaces. Steelgard® 2005 is a new innovation for use as a temper mill fluid for coated products replacing straight oils, solvents or the practice of dry tempering. In addition to preventing white rust, it produces a better “healed-over” surface, reduces roll pick-up, permits higher mill speed and achieves elongations with lower roll force. | 
